✅ Screen Size: 5.5 Inch ✅ Compatible Model: A1661 | A1784 | A1785
- LCD Assembly for iPhone 7 Plus Screen Replacement (Aftermarket / Black Color)
- Compatible With iPhone 7 Plus.
- Quality material, premium craftsmanship, and precision machining.
- Premium Oleophobic Coating helps for smooth screen operations.
- Vibrant Colors, True Tone Functionality, and Faster Refresh Rate.
- 100% Perfect fit.
- We recommend professional installation.
- Lifetime warranty on this product.
*Before you start changing the display, you should back up all your data. It is also better to first discharge yourself statically, for example by touching a heater. Apart from that, we recommend that you make sure that your workplace is clean and well lit, where you can change the display in peace and quiet. By doing so you will optimize your repair success.
* Removing the enclosure screws 2 × 3,3 mm Pentalobe You need a pentalobe screwdriver (PL1) to open the iPhone 7 Plus. Remove the two pentalobe screws at the bottom of the enclosure. They’re to the right and left of the Lightning connector. Put the screws in the same section of your magnetic pad.
* Removing the display iPhone 7 Plus - Removing the displayVideo Avoid scratching the back of the iPhone 7 by placing it on a soft and clean surface. To lift the front screen you need a suction cup, a hard plastic plectrum and a heat gun. If the screen is badly cracked, first tape it all over with package tape. The screen is glued to the frame. Heat the display around the edges using a heat gun to about 60°C. Attach the suction cup over the Home button (if possible), or next to it. While lifting the screen with the suction cup, insert the hard plastic pick between the aluminum frame and the display and press down the aluminum frame. Because the display is glued on, you have to slide the pick all around the iPhone. Don’t insert the pick too far on the side where the Sleep/Wake button is, because it could damage the display cables flex cables. Now use the pick to push the display toward the Lightning connector so the tabs come out of the aluminum frame. Rest the display on the aluminum frame, so you don’t overstretch the flex cables. If necessary, heat the outer edges of the display a few times. Don’t forget that the flex cables for the display are on the side with the Sleep/Wake button. The display is also engaged at the edge of the earpiece.
* Disconnecting the battery 1 × 2,4 mm Y-Type 3 × 1,1 mm Y-Type Battery Connector Before starting the repair, disconnect the battery contact to prevent short circuits and avoid accidentally turning on your device during the repair. Remove the three Y-Type screws using a Y-Type screwdriver (Y000) and lift off the bracket plate. Put all the parts in the same box of your magnetic pad. Now carefully pry off the battery connector by carefully inserting a spudger under it. If you don’t have a spudger, you can also try using your fingernail.
* Disconnecting the display connectors Display Connector Home Button Connector Use the spudger to disconnect the display and Home button cables.
* Disconnecting the FaceTime connector 1 × 1,3 mm Y-Type 2 × 1,0 mm Y-Type Facetime Connector Remove the three Y-Type screws using a Y-Type Screwdriver (Y000) and lift off the cover. Put all the parts in the same box of your magnetic pad. Using a spudger, carefully disconnect the FaceTime connector from the circuit board. Now you can take off the display all the way.
* Removing the earpiece 1 × 2,7 mm Phillips-Schraube 2 × 1,7 mm Phillips-Schraube 2 × 2,1 mm Phillips-Schraube The earpiece is on the back of the display unit. Remove the five Phillips screws from the bracket place on the earpiece. Put all the parts in the same box of your magnetic pad. Note that the screws have different lengths. Mixing them up could cause damage to the display during assembly. The earpiece is under the front camera’s flex cable. Fold the cable slightly to the side so you can remove the earpiece
* Removing the FaceTime cable Remove the cable set. Follow these two steps: First remove the sensors by lifting them carefully. Now insert the spudger or spatula under the flex cable at the point where the ambient microphone is. It’s firmly glued in place there. Now you can take out the cable set. Use the heat gun to soften the glue on the FaceTime cable.
* Removing the Home button Remove the four Y-type screws. Now remove the bracket plate. Put everything in the same box of your magnetic pad. Use the spudger to carefully disconnect the Home button cable. If necessary, press it against the display, because the connector isn’t screwed in. Carefully insert the ESD tweezers below the cable set and pry it loose. The cable set is usually glued in firmly. If necessary, use the heat gun to soften the glue.
As long as your cart doesn't include any battery products, we offer free worldwide shipping over $1000 Because shipping cost for "products with batteries or just batteries" is much more expensive and we recommend you to order them separately.
A. The time frame of order delivery is divided into two parts:
• Processing time: 2-3 Days
• Estimated delivery time: 5~10 Business Days
B. Shipping methods: DHL, FEDEX Express shipping
C. Shipping fee: starts from $45
We ship from Shenzhen, Guangdong China. We ship to United States, Australia, Austria, Belgium, Brunei, Bulgaria, Cambodia, Canada, Costa Rica, Croatia, Cyprus, Czechia, Denmark, Equatorial Guinea, Estonia, Finland, France, Germany, Greece, Hong Kong SAR, Hungary, India, Indonesia, Ireland, Italy, Japan, Latvia, Lithuania, Luxembourg, Malaysia, Malta, Mexico, Monaco, Mongolia, Myanmar (Burma), Netherlands, New Zealand, Norway, Philippines, Poland, Portugal, Romania, Singapore, Slovakia, Slovenia, South Korea, Spain, Sweden, Switzerland, Taiwan, Thailand, Tokelau, Trinidad & Tobago, Tristan da Cunha, United Kingdom, Vietnam, Western Sahara. If your country is not on the shipping destinations, please contact us for custom order. https://repairize.com/pages/contact